The short answer: resetting keeps your pavers and fixes what is under them. Nothing new gets bought and the patio is not torn out. Only the problem area comes up, the base gets rebuilt, and the same pavers go back in their pattern. This page covers what resetting involves, the signs you need it, and how it compares with simply cleaning or replacing the patio.
If you want to know why your pavers moved in the first place, start with why pavers sink. This page is about what happens next: putting them back.
Signs your pavers need resetting
- Low spots or dips you can see, or that hold water for hours after rain.
- Rocking pavers that move or click when you step on them.
- Trip edges where one paver sits higher or lower than the one next to it.
- Edges spreading into the lawn or mulch, with joints opening up along the border.
- Pavers lifted by roots or pushed up after a hard winter.
- Water running toward the house because the surface lost its pitch.
Stains, moss, weeds and faded color on their own do not need resetting. Those are a cleaning and re-sanding job, covered on our paver cleaning and sealing page.
How paver resetting is done, step by step
- Mark the area. We check the surface with a straightedge and find where the low or loose section starts and ends, plus a little beyond it, so the repair ties into solid ground.
- Lift the pavers. The pavers come up one at a time and are stacked in order, so the pattern goes back exactly as it was.
- Find and fix the cause. Soft, wet or washed-out material is dug out. If a root, a downspout or a missing edge caused the problem, that gets dealt with here, or the dip comes back.
- Rebuild the base. Crushed stone goes in and is compacted in layers with a plate compactor. Then a thin, level bedding layer is screeded on top, with the pitch set so water runs away from the house.
- Relay the same pavers. Each paver goes back in its spot, the section is tied into the surrounding surface and compacted, and the edge restraint is restored.
- Lock the joints. Commercial polymeric sand is swept into every joint and activated, so water and weeds stay out and the pavers stay tight.
Lifting a sunken paver and pouring sand under it raises it for a while, but the soft base below is still there. It usually drops again within a season or two. A real reset fixes the base, not just the height.
Resetting, restoring or replacing: which one you need
| What you see | What it needs | Where to read more |
|---|---|---|
| Dirty, stained, weedy or faded, but flat | Cleaning, re-sanding and optional sealing | Paver cleaning & sealing |
| A few low spots, rocking pavers or spreading edges | Resetting those areas, then clean and re-sand so it all matches | This page |
| Sinking in many places soon after it was built | Resetting larger areas on a properly rebuilt base | Paver patio repair |
| Pavers crumbling, or the base failed under most of the patio | Usually replacement | Restore vs. replace |
Most of the patios we see in Newtown, Yardley and the rest of Bucks County fall in the first two rows. Resetting is usually done as part of a paver restoration: reset the problem areas, power wash the whole surface, re-sand the joints and, if you want it, seal, so the repaired section matches the rest. Most restorations take 1 to 3 days start to finish.
Will the reset area match the rest of the patio?
Yes, because they are the same pavers. They come up and go back in their own pattern, so there is no new-versus-old color difference. Cleaning and re-sanding the whole surface afterwards evens out the joints and the look across the patio.
Can I reset pavers myself?
One or two pavers that dropped slightly can be lifted, bedded and set back by a handy homeowner with a rubber mallet, a level and some bedding sand. Anything larger, or anything that keeps coming back, needs the base dug out and compacted with a plate compactor, the pitch set correctly and the joints relocked with polymeric sand. That is where a contractor saves you doing it twice.
What paver resetting costs in Bucks County
Resetting is quoted on site, because the price depends on how big the area is and how deep the base problem goes, which nobody can see from a photo. A basic paver restoration (clean and re-sand) starts at $750, and sealing is $1.50–$2.50 per sq ft. The estimate is free, and the written quote comes before any work starts.