The short answer: sealing runs $1.50–$2.50 per sq ft, measured on the area being sealed. The square footage sets the starting point, and the condition of the surface decides where in the range it lands. A clean, flat patio with full joints sits near the low end. A patio that needs old sealer stripped, stains treated or joints refilled first costs more, because that work has to happen before any sealer goes down.
This page is about the price. If you are trying to work out whether your pavers are due for a coat at all, start with how often to seal pavers in Pennsylvania, which covers the water test and the 2-to-4-year cycle.
What the sealing price includes
A sealing price should cover more than the sealer. When we quote paver sealing in Bucks County, the per-square-foot rate includes:
- Measuring the area at the free estimate.
- Choosing the sealer for your paver type and the finish you want, natural-look or wet-look.
- Protecting what is around the pavers: siding, door thresholds, plantings, pool coping and anything else the sealer should not touch.
- Applying the sealer at the right coverage, in dry weather, so it cures evenly instead of puddling or going cloudy.
- Telling you when you can use it again: when foot traffic can go back on, and the longer wait before cars go back on a driveway.
What is not in a seal-only price is the prep a neglected surface needs first. That is the biggest reason two quotes for the "same" patio can look so different.
What moves paver sealing cost in Bucks County
Square footage
Sealing is priced by area, so a small walkway and a large pool surround are quoted very differently even at the same rate. Larger, open areas tend to sit lower in the range because the work goes faster per square foot.
Paver type and porosity
Not every paver drinks sealer at the same rate. Older, weathered concrete pavers and some tumbled or textured styles are more porous and take more product to cover properly. Denser, smoother pavers take less. Natural stone and clay brick each need their own products. We pick the sealer after seeing the paver, which is one reason we do not quote sealing blind.
The condition of the surface
Sealer locks in whatever is under it, so it only goes on a surface that is clean, dry, level and jointed. If the patio has algae, ground-in dirt, weeds in the joints or joint sand that has washed out, that has to be fixed first. On a well-kept patio that may be a light clean. On a neglected one it is a full restoration: deep clean, reset any sunken pavers and refill the joints with polymeric sand. The sealing rate does not change, but the job does.
Old sealer and buildup
If the pavers were sealed before, what is left of that coat matters. A worn-through penetrating sealer is easy to recoat. A thick, layered wet-look sealer that has gone cloudy, white or peeling usually has to be stripped before anything new can go on, and stripping is real extra work. If your sealed pavers have turned milky, our guide to white haze on pavers explains what is happening.
Stains
Oil drips, rust from furniture, leaf tannins and grill grease show up even more once sealed, because the sealer deepens the color. Stains are treated before sealing where they can be.
We price by square foot after a free on-site estimate. You get the sealing price and any prep work as separate lines in a written quote before any work starts, so you can see exactly what is sealer and what is restoration.
Seal only, or restore and seal?
Most calls about sealing cost are really asking one question: can I just seal it? Sometimes, yes. Here is how it usually breaks down.
| If your pavers are… | What they need | How it is priced |
|---|---|---|
| Clean, flat, joints full, water no longer beading | A clean and seal | Sealing at $1.50–$2.50 per sq ft |
| Dirty or green, some joint sand gone, still flat | Clean, re-sand with polymeric sand, then seal | Restoration from $750, plus sealing |
| Sunken spots, rocking pavers, weeds throughout | Reset the low areas, then clean, re-sand and seal | Restoration plus resetting, quoted on site |
| Cloudy, peeling or patchy old sealer | Strip the old coat, then reseal | Quoted on site once we see the sealer |
A basic paver restoration and sealing visit starts at $750 for the clean and re-sand, with sealing added to the same visit. Doing it in one trip matters: the sealer goes on once the new joint sand has cured, so the joints are protected from the first rain.
What skipping the sealer costs
Sealing is optional. Pavers are not ruined without it. But in Bucks County, freeze-thaw winters, shade and leaf drop are hard on bare pavers. Unsealed joints lose sand faster, weeds and ants move in, color fades and stains soak in for good.
The comparison worth making is not sealing against nothing. It is sealing against the day a neglected patio gets bad enough that someone suggests tearing it out. Replacement means new pavers, a new base and a much bigger, custom-quoted job, while most worn patios can be brought back for a fraction of that. Our restore vs. replace guide walks through how to tell which one your patio actually needs.
DIY sealing vs. hiring a pro
You can seal pavers yourself, and on a small, healthy patio it can go fine. The cost of DIY is mostly the sealer, a sprayer or roller, and a weekend. Where it goes wrong is the prep and the conditions, not the product:
- Sealing over dirt, algae or efflorescence traps it under the coat for years.
- Sealing over damp pavers or with rain coming is the most common cause of a cloudy, white finish.
- Putting it on too thick, especially wet-look sealer, leaves a slippery surface that peels.
- Sealing over empty joints leaves the weak spot unprotected. The joints need polymeric sand first.
A failed DIY coat usually has to be stripped before a professional can reseal, which costs more than doing it once. If the patio needs more than a clean and seal, that prep is the part most homeowners hand off.
How to compare sealing quotes
When quotes are far apart, the difference is almost never the sealer. Ask each company:
- What is the price per square foot, and what area did you measure? A lump sum with no area makes quotes impossible to compare.
- Is cleaning included, and how? High-pressure washing with a narrow tip can blast out joint sand. Ask how the joints are handled.
- Are the joints being re-sanded? And with what: commercial polymeric sand or plain sand?
- Which sealer, and which finish? Natural-look and wet-look products behave differently and age differently.
- What happens to the old sealer? If there is buildup, is stripping included or extra?
- Is the company insured and registered? In Pennsylvania, home improvement contractors register with the Attorney General. Ours is PA HIC #PA223446.