Soft washing vs. pressure washing · Free estimates · Bucks County PA Get Estimate
Home/Blog/Soft washing vs. pressure washing
Exterior cleaning · Bucks County, PA

Soft washing vs.
pressure washing

Soft washing cleans with low pressure and a cleaning solution that kills mold, mildew and algae at the root, so it is the right method for siding, painted trim and decks. Pressure washing uses high-pressure water to scour hard surfaces like concrete, driveways, stone and pavers. Most homes need some of each, on different surfaces.

6 min readUpdated November 18, 2026Written by the crew that does both

The short answer: soft washing lets the solution do the work; pressure washing lets the water do the work. Use soft washing where high pressure would cause damage, and pressure washing where the surface is hard enough to take it. Picking the wrong one is how siding gets cracked, paint gets stripped and paver joints get blasted empty.

The two terms get used interchangeably, and a lot of homeowners assume "soft wash" is just a gentler setting on the same machine. It isn't. The two methods clean in different ways, and each one is the wrong tool for some parts of your home.

What soft washing is

Soft washing applies a professional cleaning solution at low pressure, roughly what a garden hose puts out. The solution breaks down the organic growth that makes a house look dirty: mold, mildew, algae, lichen and the black streaks that run down siding from the roofline. It is left to dwell for a few minutes, then rinsed off at low pressure.

Because the solution kills the growth instead of knocking the top layer off, the clean lasts. Growth that is only blasted off the surface tends to come back within weeks, because the roots are still there.

What pressure washing is

Pressure washing uses high-pressure water to physically scour dirt off a surface. On a driveway, a concrete walkway or a set of stone steps, that is exactly what you want: ground-in dirt, tire marks and green film come off, and the surface can take the force. Pros clean flat concrete with a rotary surface cleaner rather than a handheld wand, so the clean is even and doesn't leave the striping you see on a lot of DIY driveways.

"Power washing" usually means the same thing, sometimes with heated water. The name matters less than the pressure that hits the surface.

Side by side

 Soft washingPressure washing
How it cleansA cleaning solution breaks down growth; low pressure rinses it offHigh-pressure water scours the surface
Best forVinyl and fiber cement siding, stucco, painted trim, wood and composite decksConcrete driveways, sidewalks, steps, stone and pool surrounds
PaversLow-pressure soft washing for routine cleans that keep joint sand in placeControlled pressure for a deep clean, followed by re-sanding
What it removesMold, mildew, algae, lichen, black streaksGround-in dirt, tire marks, surface grime and growth on hard surfaces
Main risk if misusedSolution on plants if they aren't rinsed and protectedCracked or forced-in siding, stripped paint, furred wood, etched concrete, empty joints

Why high pressure damages siding, wood and paint

Vinyl siding is built to shed rain coming down, not water driven sideways and upward. A pressure wand aimed at it forces water behind the panels, where it soaks the sheathing and can lead to mold inside the wall. High pressure can also crack older, brittle vinyl, blow out caulk joints and strip paint off trim.

Wood decks are just as easy to hurt. Too much pressure raises and furs the grain, leaving the boards rough and splintery, and it can gouge soft spots that are permanent. Composite boards scar. Stucco can be pitted. That is why decks are washed at low pressure, and why siding and trim are always soft washed. Our house washing page walks through how a house soft wash is done, step by step, including how surrounding plants are pre-rinsed and protected before any solution goes on.

What about roofs?

Petra Power Solutions does not offer roof cleaning. We wash siding, trim, decks and hard surfaces.

Where pressure washing is the right call

Hard, dense surfaces need more than a solution and a rinse. Concrete driveways hold dirt and tire marks in their pores, and stone steps and walkways collect grime that a low-pressure rinse won't move. That is the work our pressure and soft washing service handles: driveways, sidewalks, concrete patios, steps and pool surrounds, each at the pressure that surface can take and no more. Even on concrete, too much pressure from a narrow tip held too close can etch the surface and leave permanent marks, which is why the rotary surface cleaner matters.

Pavers sit in the middle

Paver patios and walkways are the surface people get wrong most often. The pavers themselves are hard enough for pressure, but the sand in the joints is not. A high-pressure clean blows that sand out, and empty joints let weeds root, let water get under the pavers and let sections loosen and sink.

So pavers get two different treatments depending on the goal:

  • Routine cleaning: a low-pressure soft wash takes off algae, moss and mildew without disturbing the joint sand or sealer. That is how our patio maintenance visits work.
  • Restoration: a deep clean at controlled pressure deliberately removes the old, dirty joint sand along with the grime. The joints are then refilled with polymeric sand and, if you want, sealed. That is a paver restoration, which starts at $750, with sealing at $1.50–$2.50 per sq ft.

What you never want is a hard pressure wash with nothing after it. The patio looks great for a week, then the empty joints fill with seeds and the weeds come back worse. More on that in how to stop weeds between pavers.

Clean before you replace

A lot of siding, driveways and patios that look worn out are just dirty. Green siding on the north side of a house, a black-streaked driveway or a dull, weedy paver patio can all look like they are at the end of their life, and most of the time a proper wash, the right method for each surface, shows otherwise. For patios in particular, cleaning, re-sanding and sealing usually costs a fraction of tearing the pavers out. Our restore vs. replace guide explains how to tell when restoration will work and when replacement is really needed.

How often each one is needed in Bucks County

Humid Pennsylvania summers grow mold and algae quickly on shaded and north-facing walls, so most homes here benefit from a house soft wash every 1 to 2 years. Driveways and concrete are usually washed when they look dirty, often once a year or before an event or a sale. Paver patios do best with a yearly low-pressure clean and a reseal only when water stops beading, which is the routine behind our care plan.

What it costs

Washing is priced by the surface and its size, the height of the home and how much buildup there is. Current starting prices are on our house washing and pressure washing pages, and every job gets a written quote after a free estimate. Most washing jobs can be priced from a few photos.

Common questions

→What is the difference between soft washing and pressure washing?

Soft washing uses low pressure and a cleaning solution that kills mold, mildew and algae at the root. Pressure washing uses high-pressure water to scour dirt off hard surfaces. Soft washing is for siding, painted trim and decks; pressure washing is for concrete, driveways, stone and pavers.

→Is soft washing better than pressure washing for vinyl siding?

Yes. High pressure can force water behind vinyl panels, crack older siding and strip paint from trim. A soft wash cleans the siding at low pressure and kills the growth instead of just blasting the surface, so it lasts longer too.

→Can you pressure wash pavers?

Yes, at a controlled pressure, but it removes the joint sand along with the dirt. After a pressure clean the joints have to be refilled, ideally with polymeric sand, or weeds and water get in. For routine cleaning, a low-pressure soft wash keeps the joint sand in place.

→Is the soft wash solution safe for my plants?

When it is handled properly, yes. Plants and landscaping are rinsed before any solution is applied, sensitive plants are covered, and everything is rinsed again afterward. Properly diluted and rinsed, the solution does not harm established landscaping.

→Should a wood deck be soft washed or pressure washed?

Washed at low pressure. High pressure raises and furs the grain of wood and scars composite boards. We clean deck boards and railings at low pressure; we don't build or stain decks.

→Do you clean roofs?

No. Roof cleaning is not a service Petra Power Solutions offers. We soft wash siding, trim and decks and pressure wash driveways, concrete and pavers.

→Is power washing the same as pressure washing?

Close enough for most homeowners. Both use high-pressure water; power washing sometimes means the water is heated. Either way, it belongs on hard surfaces like concrete and stone, not on siding or wood.

Next question

Keep reading.

Get started

The right wash
for every surface.

Free estimate, often from photos. Owner on every job, fully insured, and the pressure each surface can take and no more.

Now booking December · Weekend slots fill first
Call (267) 331-1990 Get a Free Estimate

No obligation·Free estimate often by photo·61 Google reviews, 5.0★·Newtown, PA

Serving Bucks County, PA

Petra Power Solutions builds and restores hardscape across Newtown PA, Yardley PA, Doylestown PA, New Hope PA, Langhorne PA, Richboro PA, Horsham PA, Jamison PA, Washington Crossing PA, and Buckingham PA. Owner-operated since 2022. Free estimates. Call (267) 331-1990.

Free Estimate Call Now